fbpx
联系我们

    联系表格



    请注意,提交此表格
    即表示您同意我们的 条款细则隐私政策
    我们认为邦腾有很多有趣的新闻可以与您分享。请在下方打勾再次确认您希望收到我们的来信,我们会把您的详细信息添加到我们的邮件列表中。我们确保绝不会把您的联系方式传递给任何第三方。
    电子邮件

    英国邦腾科技深圳代表处
    深圳市南山区粤海街道粤美特大厦902 房

    Tessera Processor Software 2.2.6

    2nd 10月 2019
    2.2.6 Issue A
    2.2.3
    Processor Firmware
    Tessera Remote
    Tessera Control

    Compatibility Note

    Panels upgraded to 1.5 firmware or later will not be discovered by or communicate with a processor running firmware 1.4.2 or earlier due to a protocol change. To downgrade these panels back to 1.4, use a processor running 1.4.3 or 1.4.4 to push firmware to them.

    Panel On-Screen Display (OSD)

    The new Panel OSD provides detailed status information right on your panels.

    • To enable OSD, select the fixtures you wish to display the OSD on, and click the ‘OSD’ button in the DEVICE window
    • Sections can be cycled through using the left and right arrows next to the OSD button
    • Further pages of the same section (if applicable) can be paged through using the up and down arrows next to the OSD button
    • Supported by all processors, in both remote and local UI
    • Supported only by R2-based panels with at least 64×64 pixels
    • Includes Panel Information, Module Information, Ethernet Information, Video Status, Calibration Information, I/O Status, Temperature plots and Error plots

     

    Processor Redundancy for Tessera SX40

    Please observe the topology below to correctly configure your SX40 system for Processor Redundancy.

    • Both processors may be fed from the same video source if required. HDMI/SDI through can be used, but isn’t recommended; an upstream splitter is preferable
    • Each processor may be fed from a completely independent video source if required. These may be different formats (HDMI/SDI), resolutions, framerates, etc. – there’s no requirement for any aspect of the sources to match
    • Can be used with or without closed loop redundancy (image above shown with closed loop redundancy)
    • XD firmware must be updated for redundancy to function correctly
    • Failover, when triggered, takes approximately 2-3 seconds for panels to be re-associated to the backup processor, during this time, no video will be shown
    • Once the system has been cabled correctly, redundancy should be enabled and the correct role set for each processor under the Failover tab

     

    Chinese Language Support

    Our processor User Interface now has Chinese language support. This can be accessed from the Preferences menu, under the Language section using the change language dropdown. ​

     

    90 Degree Rotation for Tessera SX40

    Fixtures can now be rotated in increments of 90 degrees on the Tessera SX40 LED processor.

     

    Known Issues

    Restore factory defaults/format SD card can cause fixture library instability
    ​If you perform either of these operations please reboot your processor before browsing to the fixture library window as this may otherwise be unstable.​

    ​Settings from Tessera Control are not applied to newly discovered fixtures
    If using Tessera Control to alter Brightness, Temperature or Gamma, these settings are not sent to newly discovered fixtures until a change is made to the value. ​

    ​Tessera Remote and Tessera Control may not work on Mac OSX El Capitan
    When running on a Mac OSX El Capitan the Tessera Remote and Tessera Control applications can fail to detect network ports. This appears to be limited to cases where no default gateway is specified on the computer’s network interface.

    In situations where no default gateway is set using DHCP, we recommend specifying a default gateway manually. PCs running Windows and Macs running OSX Yosemite or earlier are not affected. ​

    Tessera Remote may fail to import project files
    In some cases Tessera Remote may fail to import project files from local storage. As a workaround create the project from scratch, or use a local monitor, keyboard and mouse to import the project file before connecting with Tessera Remote. ​

    ​Some input devices on KVM switches do not work
    We have had reports that trackpads may not function correctly when connected to the processor via a KVM switch. As a workaround we recommend using a mouse, or connecting input devices directly to the processor’s USB ports. ​

    Monitors connected via DisplayPort-to-VGA adapters may be unstable
    Local user interface monitors connected to the processor via certian active DisplayPort-to-VGA adapters may give an unstable image or the monitor is not detected at all. As a workaround we recommend using a DVI or DisplayPort monitor.